Teledyne LeCroy Digital Oscilloscope
Teledyne LeCroy Digital Oscilloscope at TestMart are of the highest quality in test equipment industry. We strive to present
only the highest quality information in an unbiased and neutral fashion. We focus on presenting the most
current information of product pricing and availability.
|
Manufacturer |
Model |
Condition |
Description |
Specs |
Teledyne LeCroy |
PP018-1 |
New (GSA discount) |
500 MHz Passive Probe for HDO, 10:1, 10 MOhm |
PP018-1 |
Teledyne LeCroy |
PP017-1 |
New (GSA discount) |
250 MHz Passive Probe for HDO4000, 10:1, 10 MOhm |
PP017-1 |
Teledyne LeCroy |
HDO6K-XDEV |
New (GSA discount) |
Advanced Customization Option for HDO6000 |
HDO6K-XDEV |
Teledyne LeCroy |
HDO6K-USB2bus-TD |
New (GSA discount) |
USB 2.0 Trigger and Decode Option for HDO6000 |
HDO6K-USB2bus-TD |
Teledyne LeCroy |
HDO6K-USB2-HSICbus-D |
New (GSA discount) |
USB 2.0 HSIC Decode Option for HDO6000 |
HDO6K-USB2-HSICbus-D |
Teledyne LeCroy |
HDO6K-UART-RS232bus-TD |
New (GSA discount) |
UART-RS232 Trigger and Decode Option for HDO6000 |
HDO6K-UART-RS232bus-TD |
Teledyne LeCroy |
HDO6K-SPIbus-TD |
New (GSA discount) |
SPI Trigger and Decode Option for HDO6000 |
HDO6K-SPIbus-TD |
Teledyne LeCroy |
HDO6K-SOFTCASE |
New (GSA discount) |
Soft Carrying Case for HDO6000A |
HDO6K-SOFTCASE |
Teledyne LeCroy |
HDO6K-SDM |
New (GSA discount) |
Serial Data Mask Software Package for HDO6000 |
HDO6K-SDM |
Teledyne LeCroy |
HDO6K-PWR |
New (GSA discount) |
Power Analysis Option for HDO6000 |
HDO6K-PWR |
Teledyne LeCroy |
HDO6K-LINbus-TD |
New (GSA discount) |
LIN Trigger and Decode Option for HDO6000 |
HDO6K-LINbus-TD |
Teledyne LeCroy |
HDO6K-JITKIT |
New (GSA discount) |
Clock, clock-data Jitter Analysis and views of time, statistical, spectral, and jitter overlay |
HDO6K-JITKIT |
Teledyne LeCroy |
HDO6K-I2Cbus-TD |
New (GSA discount) |
I2C Trigger and Decode Option for HDO6000 |
HDO6K-I2Cbus-TD |
Teledyne LeCroy |
HDO6K-FLEXRAYbus-TD |
New (GSA discount) |
FlexRay Trigger and Decode Option for HDO6000 |
HDO6K-FLEXRAYbus-TD |
Teledyne LeCroy |
HDO6K-ET-PMT |
New (GSA discount) |
Electrical Telecom Mask Test Package |
HDO6K-ET-PMT |
Teledyne LeCroy |
HDO6K-EMC |
New (GSA discount) |
EMC Pulse Parameter Software Package for HDO6000 |
HDO6K-EMC |
Teledyne LeCroy |
HDO6K-DPHYbus-D |
New (GSA discount) |
MIPI D-PHY CSI-2, DSI Bus Decode option for HDO6000 |
HDO6K-DPHYbus-D |
Teledyne LeCroy |
HDO6K-DIGRFV4bus-D |
New (GSA discount) |
DigRF V4 Bus Decode option for HDO6000 |
HDO6K-DIGRFV4bus-D |
Teledyne LeCroy |
HDO6K-DIGRF3Gbus-D |
New (GSA discount) |
DigRF 3G Bus Decode option for HDO6000 |
HDO6K-DIGRF3Gbus-D |
Teledyne LeCroy |
HDO6K-DFP2 |
New (GSA discount) |
Digital Filter Software Package for HDO6000 |
HDO6K-DFP2 |
Example usage
The classic use of a scope is to diagnose a failing piece of
electronic equipment. In a radio, for example, one looks at the
schematic and tries to locate the connections between stages (e.g.
electronic mixers, electronic oscillators, amplifiers).
Then one puts the scope's ground on the circuit's ground, and
the probe of the scope on a connection between two of the stages in
the middle of the train of stages.
When the expected signal is absent, one knows that some
preceding stage of the electronics has failed. Since most failures
occur because of a single faulty component, each measurement can
prove that half of the stages of a complex piece of equipment
either work, or probably did not cause the fault.
Once the failing stage is found, further probing of the
defective stage can usually tell a skilled technician exactly which
component is broken. Once the technician replaces the component,
the unit can be restored to service, or at least the next fault can
be isolated.
Another use is to check newly designed circuitry. Very often a
newly-designed circuit will misbehave because of bad voltage
levels, electrical noise or design errors. Digital electronics
usually operates from a clock, so a dual-trace scope is needed to
check digital circuits. "Storage scopes" are helpful for
"capturing" rare electronic events that cause defective
operation.
Another use is for software engineers who must program
electronics. Often a scope is the only way to see if the software
is running the electronics properly.